zephyrtie31
User Name: You need to be a registered (and logged in) user to view username.
Total Articles : 0
https://www.g28carkeys.co.uk/fiat-car-key-replacements-near-me/
Reasons Your Fiat 500 Key Fob Wont Work A key fob from Fiat 500 is a great way to open the doors and begin the car There are a myriad of reasons why the key fob might stop working This includes a dead coinbattery or water damage receiver modules issues and interference This listing is for an NEW replacement Fiat Flip Key Remote like the Ilco brand that must be professionally programmed by a local locksmith click here for Locksmith Search It comes with lock unlock and trunk buttons Dead Coin Battery The most frequent reason that your 500 key fob wont function is due to an inactive battery Modern key fobs have a limited operating range and must be within only a few feet from the vehicle in order to function If you are further away from your vehicle and press the keyfob button it will not respond and display the message Key Fob Not Detected If this happens then replace the battery for your coincell Part Number CR2032 by a fresh one from a reputable brand like Panasonic Duracell or Energizer You can usually find them at your local hardware store or online You can test the battery in the coincell by pressing the buttons while standing near your Fiat 500 The car should flash its parking lights and the key fob should operate the lock and unlock switches If the key fob wont function after replacing the battery it could have water damage that stops it from communicating with the receiver module inside your car Water damage can happen in many ways such as an easy splash or submerging the key fob into saltwater at the beach If you suspect that your fob has been exposed to water you can place it in a bag of rice to draw out the moisture If this doesnt work you will need to have your fob replaced by an auto locksmith or a dealer Water Damage Damage to the water supply can occur if you submerge the fob in the ocean or wash it in a machine Saltwater poses a particular risk to the circuit board of the fob that can cause it to short out and eventually die Getting the fob wet is not an ideal choice however if you drop it into a cup of water or fail to remove it from your pants pocket before running the washing machine and you dont have a chance dont give in First take the battery off the fob Before replacing the battery clean the electronic chip using isopropyl or a similar product Test the fob afterward to check if its working If the key doesnt function then it might need to be programmed again This is usually done by a dealer or professional auto locksmith If the key you have is older and is not programmed for your car you will need to replace it completely A professional locksmith for cars can carry out this simple task The locksmith will have to cut the key to match the ignition of your car cylinder needs to program your fob into the vehicles system This is an affordable and quick process that can be completed in the same day Receiver Module Issues One of the most common reasons your 500 key fob may stop functioning is because its out of range The remote has a maximum range of 30 feet So should you be too far from your vehicle it wont respond to your commands This can be easily fixed by moving closer to your vehicle until it starts responding If your fob doesnt work after replacing the battery for the coin also called a button watch or button it could be a problem with the circuit board inside In the majority of cases reprogramming your fob will fix the problem There are instructions on how to do this on the majority of vehicles by searching YouTube or looking through the owners manual Its possible that you need to replace the metal retaining clips that keep the coin battery If they lose tension it could prevent the battery from sitting properly and this will cause your remote to malfunction In rare cases the fob might be out of connection with your vehicle as a result of hardware or software issues It is possible to fix this issue by visiting your local autolocksmith or dealer to reprogram your key fob In certain situations they may need to install the software again in your body control module too Interference In addition to a dead battery on a coin The key fob may not be able to transmit or receive an signal due to interference This can happen when the key fob is close to an electronic radio transmitter cell phones radar detectors or any other source of electromagnetic radiation Other reasons the key fob might not function include a poor connection to the buttons and internal chip or water damage If the key fob has suddenly stopped working without notice or after trying everything you can do at home to solve it eg You could have a malfunctioning 500 receiver module If youve tried replacing it with a battery reprogramming or using an alternative key fob The receiver module which is located under the dashboard is able to pick up radio frequency signals from your key fob Then it converts them into electronic commands that the vehicle interprets Fortunately theres an easy way to reset all of the onboard systems in your 500 including the key fob Disconnect the battery for 15 minutes by removing first the negative cable then the positive cable Then reconnect the battery This will eliminate any remaining electrical charge and then restart the cars computer This could help you get your key fob to function again If the problem persists you should speak with an expert certified technician They will be able diagnose the exact cause of problems