tondoll00

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/patio-door-repairs-epsom/

How to Fix Sliding Patio Door Track Repair The sliding patio doors are gorgeous and practical however they can develop problems in time making them difficult to operate These problems are often caused by dirty or damaged tracks or rollers They can be fixed using WD40 and a thorough cleaning Use your vacuum cleaner to clean any heavy dirt and debris Then scrub the track using a brush and cleaning product as you move the door forward and backwards often Apply a siliconebased grease to decrease friction Repairing Dented Tracks Patio doors are an attractive addition to any home but when they stop sliding or dont open smoothly it can be a frustrating experience In most cases you can restore the smooth operation of your sliding door by following a few easy steps The main reason for stuck or difficult to move door is the accumulation of dirt within the track channels The best solution to fix this is to remove the door from the track and clean it thoroughly You can make use of a toothbrush to get rid of the dirt and grime that is deeper Once the track is cleaned a siliconebased grease can be applied to stop future problems It is also essential to inspect the rollers for damage or misalignment The rollers sit at the bottom of the doors and help guide them along the track If they are damaged or misaligned the doors may be difficult to move and may require replacement Examine the tracks visually to look for any bends or dent Inward bends can pinch and bind a door whereas outward bends could throw the rollers away or hinder them If you notice bent areas of the track you can straighten them by using pliers a hammer or a block of wood However more severe bends may require professional assistance for repair If these fixes dont work it could be necessary to replace the entire track In this situation you can find kits at most hardware stores that allow you to lay a new track over the old one and screw it in place Track replacement kits are available in various lengths and can be cut to fit your particular doors Its recommended to take note of this to check if your track is deforming breaking or showing signs of wear The professionals can usually identify the problem and offer an efficient and safe solution Repairing Broken Tracks Dirt or damage to the track can cause the door to become stuck or difficult to open The accumulation of dirt and debris over time If your tracks are bent or damaged they might require professional repair or replacement You can diagnose the problem yourself and fix it First check the track to ensure it is not blocked by anything other than rust or dust If the track is obstructed by something other than dust or rust cleaning it thoroughly with a brush using mild detergent will remove any obstructions and restore smooth motion Then examine the rollers to ensure they are not sticking or catching A damaged or broken door roller could cause it to become stuck It can also lead to further damage to the track that requires repair or replacement by a professional If the rollers are not broken you may be able to resolve the problem by oiling them A siliconebased lubricant may help reduce friction between the tracks and the rollers making it easier for the door to slide A roller that is not aligned properly can make your sliding door stick or be difficult to operate To fix this locate the screws that adjust the rollers and adjust them until they are properly aligned with the track Another reason that can cause an unmovable or stuck patio door is the worn weather stripping You can easily replace the weather stripping by taking it from the bottom of the fixed panel and also from the jamb with the screwdriver Then you can pull the old strip out and sink the new one in If your track is severely bent you should give it to a professional patio contractor They will be able to fix the problem and ensure that the track is securely in place without further damage or bending If your track is bent or kinked you can straighten it with a pair of metalbending pliers If you are unable to straighten the track on your own use a rubber hammer and a piece of wood Continue to pound the bent section until it is straight Repairing Damaged Rollers If your sliding patio door is a bit noisy or difficult to roll the cause may be your rollers They can become stiff and dirty over time causing the door to be pushed against the track and then become noisy To solve the issue clean the bottom track first then lubricate your rollers After the rollers have been cleaned you can put the door back on its tracks This is a good moment to attach any clips or braces that kept the door in place while it was removed from the frame It is best to have a friend help you lift up the sliding patio door and tilt it toward you This will lift it from the bottom track Set the sliding patio door on a solid flat surface such as a table or sawhorses Remove any grilles or drapes from the doors Remove any screws holding the head stop molding Photo 2 This step may not be required on older doors made of aluminum but it is recommended in the event that you have it Then take out the adjustment screw for the rollers on each end of the frame This screw regulates the rollers height and turning it clockwise lowers the rollers while turning it counterclockwise raises them It is helpful to have a friend nearby to assist you in disengaging the rollers Youll require tools such as the screwdriver that has Phillips heads and a prybar or a stiff putty knife to accomplish this After the rollers have been removed remove the dust cap from the wheel mechanisms and clean them Then clean the roller surfaces with alcohol to remove any dirt or residue After the rollers are cleaned apply lubrication using an lubricant made of silicone that smothers dirt and helps keep them moving effortlessly Reinstall the door by putting the top portion of the doors on the track and then bringing the bottom part in Reinstalling the rollers into the frame of the track at their highest point is crucial This will allow the doors to slide into place easily without rubbing on the tracks Repairing Damaged Wheels Often a patio door drags because the wheels have worn out Replace the wheels if necessary Clean patio door panel to prevent grit from destroying the wheels If the tracks are bent straighten them using pliers or by holding the block of wood against the bent area and pounding it with the hammer If the wheels still wear out you can use a track sill See Photo 5 Installation is easy and takes less than a half hour