tigernurse24
User Name: You need to be a registered (and logged in) user to view username.
Total Articles : 0
https://www.g28carkeys.co.uk/fiat-car-key-replacements-near-me/
Reasons Your Fiat 500 Key Fob Wont Work A key fob for Fiat 500 makes it simple to open doors and start your vehicle However there are many reasons why the fob wont be functioning These include a dead battery damage to the receiver module water issues and interference This listing is for a NEW replacement Fiat Flip Key Remote lookalike Ilco brand that needs to be professionally programmed by a local automotive locksmith click here to search for a Locksmith Search This remote includes trunk lock and unlock buttons Dead Coin Battery The most frequent reason why your 500 key fob will not function is a dead battery Modern key fobs only have an operating range that is limited and must be within just a few inches of the vehicle in order to function If you are further away from your vehicle and you press the keyfob button it wont respond and display the message Key Fob Not Detected If this happens replace the coincell battery Part Number CR2032 by a new one of a trusted brand such as Panasonic Duracell or Energizer You can find them at your local hardware store or on the internet fiat doblo key programming can test the battery on your coincell by pressing the buttons while standing near your Fiat 500 The car should blink its parking lights and the key fob will operate the lock and unlock switches If the key fob wont work after replacing the battery it could be damaged by water that blocks it from connecting to the receiver module inside your vehicle Water damage can occur through a variety of methods including an easy splash or submerging your key fob in saltwater at the beach If you suspect your fob was exposed to water try placing it in a dry rice bag to pull the moisture back out If this isnt working youll require your fob to be reset by an auto locksmith or dealer Water Damage Although the fob is equipped with rubber seals that keep water from the electronic chip inside submerging it in the ocean or washing it in a machine could cause water damage Saltwater can cause the circuit board to become shorted and eventually end up dying Getting the fob wet is not a good idea but if you drop it into a glass of water or forget to remove it from your pants pocket before running the washing machine Dont give up hope First remove the battery Before replacing the battery clean the electronic chip with isopropyl or similar products Then test the fob to verify if it is working If the key doesnt function then it might need to be reset This is usually done by an auto locksmith or dealer If the key you have is older and not programmed to work with your vehicle You will need to replace it completely This is a simple process that can be handled by a professional automotive locksmith The locksmith needs to cut the key to match the ignition in your vehicle The locksmith will also have to reprogram your fob in the vehicles system This is a fast and affordable process that can usually be completed within the next day Receiver Module Issues One of the main reasons why your 500 key fob may stop functioning is that its out of range The remote has a range of 30 feet Therefore in the event that you are far away from your vehicle it wont respond to your commands Its easy to solve this issue by moving the remote closer to your car until it responds If youve replaced the coin battery commonly called a button or watch and the fob wont work it could have an internal circuit board problem In the majority of cases reprogramming your fob will fix the problem You can find the instructions for the majority of vehicles on YouTube or in the owners guide It is possible to replace the metal retaining clips that keep the battery of your coin in place If they lose tension they could stop the battery from being properly seated and can result in the malfunction of your remote In rare instances the fob could be out of the vehicles sync because of software or hardware problems This issue can be fixed by visiting your local autolocksmith or dealer to reprogram your key fob In certain situations they might need to reinstall the software in your body control module as well Interference In addition to a dead battery on a coin The key fob might not be able to receive or transmit a signal due to interference This can happen when the key fob is located near radio transmitters cell phones radar detectors or another source of electromagnetic radiation The key fob might not work because of a weak connection with the buttons water damage or damage to the internal chips If the key fob has been unable to function for a while without notice or even after trying every option at home to solve it eg replacing batteries reprogramming or using the spare key fob you may have a malfunctioning receiver module on your 500 The receiver module is located under the dash and is able to pick up the radio frequency signals from the key fob It converts them into electronic commands that the vehicle interprets There is a straightforward method to reset the 500s internal system including the keyfob Disconnect the battery for 15 minutes by removing first the negative cable then the positive cable Then reconnect the battery This will clear any residual electrical charge and then restart the computer of your car This will help you get your key fob working again If the issue persists you should seek out an expert technician They will be able to identify the root cause of any issues