loafcap7

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.mymobilityscooters.uk/

Mobility Scooter Mechanic Near Me A scooter is an expensive investment If you take care of your scooter you can take advantage of it for many years You can also finance it buy a used one or see whether its covered by your insurance The life of batteries varies but with proper use it can last for up to two years But its essential to maintain the batteries and the scooter Batteries with problems As with any mechanical device mobility scooters are prone to occasional breakdowns Thankfully most problems can be easily diagnosed and fixed This can save lots of time money and hassle The best method to avoid the mobility scooter from breaking down is to perform regular maintenance and to practice preventative maintenance This will enable the scooter to run longer and reduce the chance of it crashing during use It is vital to avoid overcharging the battery as it can reduce the batterys lifespan It is also recommended to keep the scooter inside especially in bad weather Doing so will protect the battery from extreme temperatures and humidity which can cause it to degrade faster than normal If your scooter is cutting when you ride the most likely cause is a blown fuse or tripped circuit breaker It is recommended to contact an expert immediately to fix the scooter It is also recommended to choose an escooter brand that has local warehouses and service centers so that you can have your scooter repaired in a timely manner A malfunctioning potentiometer may cause your scooter not getting started A defective potentiometer could cause the throttle to fluctuate making it difficult to regulate your speed It is easy to replace a damaged potentiometer with an entirely new one however this job should only be undertaken by someone with electrical experience Another way to determine whether the potentiometer is causing the problem is to use a multimeter The potentiometer should be located at the back of your controller right next to the throttle pot There will be two pieces one of which has small wires and the other one will have magnets Make sure both pieces are separated and not stuck together Then trace the power cable to the lift on the bottom of the controller You can then test for voltage It should show 12 Volts Incorrect ignition switch The ignition switch is what is the electrical power source for your vehicle The ignition switch is situated in the steering column behind the cylinder that controls the ignition key Over time your ignition switch will begin to wear out and eventually fail The electrical contacts of the switch are responsible for the wear and tear These contact points will become corroded or worn and they are unable to make the electrical connection to the vehicles starter solenoid or battery In the worstcase scenario the switch may burn out completely It is often difficult to determine the symptoms of a defective switch The first sign of a problem is the inability to start the engine This is usually due to an improper ignition or miscoded engine computer It could also be the result of by the ignition sensor or fuel injections have a problem A damaged ignition switch could be noticed when the car wont shut off after turning off This is likely to be a problem with the ignition switch or the ignition lock Locksmiths can fix the ignition switch if it is the reason To test the ignition turn off the engine first Then disconnect the negative cable Then connect the positive probe of a multimeter to the power feed wire from the switch and the negative probe to any unpainted metal in the car Set the multimeter to read voltage If the reading is less than 90 percent of the batterys voltage the ignition switch may be defective If the readings are normal then the problem could be a worn out key or a faulty lock In this case you can try with a spare key or have an expert locksmith make an entirely new key Potentiometer that isnt working There are several possible reasons for why your scooters potentiometer isnt functioning correctly The most common reason is that the internal pin of the potentiometer is broken It could also happen if the carbon film is burnt In this case resistance will be infinite There is no change in the current or voltage of the circuit once you adjust the knob To check this you can connect an electronic multimeter to the middle wiper connector and test the potentiometers resistance If the reading is 0 it means that the pin inside the potentiometer has failed MyMobilityScooters is to use an oscilloscope to check the location of the middle wipers connection This will show you if the middle wiper is in the centre or not Another reason for a malfunctioning potentiometer is because the switch structure has been damaged This is caused by contact oxidation and is fixable with certain methods Other issues with the potentiometer include excessive noise from rotation and damage to the resistor body or switch When your mobility scooter or power chair malfunctions it can be very frustrating It can negatively impact your quality of life and hinder you from doing what you love Fortunately there are many ways to fix your equipment quickly and inexpensively These strategies will help you save money and time and help protect your warranty They can help you regain your freedom and lead a healthier life You could even be eligible for a loaner in the interim Flat spots If you use your mobility scooter to traverse uneven terrain or rough surfaces it is a great idea to inspect the tyres regularly for signs of wear and tear This is particularly important in the event that your pneumatic tires may be punctured by sharp objects Replace your tyres if observe that they are beginning to begin to show signs of wear before they become flat The speed potentiometer in the scooter is an essential part of the device and can cause issues if it gets damaged It is exposed to moisture and other elements This can lead to corrosion This could result in the device becoming malfunctioning causing it to move at different speeds If you are experiencing this issue its a good idea to contact an expert mobility scooter technician and have the potentiometer replaced immediately The ignition switch is another frequent issue Its susceptible for corrosion This can cause the ignition switch to become stuck or break off It is important that you go through the instruction manual for your scooter when you spot this problem Another issue that is common to mobility scooters is that the battery can run out of power This could be a huge issue for people who depend on their mobility scooter to travel If you notice that your mobility scooter isnt as efficient as it did previously this is a sign that the battery is in need of replacement Tires that are worn out Mobility scooters can be an amazing device for a variety of people but especially disabled and elderly Like any mechanical device they are likely to be prone to issues from time some point Certain preventative maintenance techniques will help you avoid the majority of these issues These tips include checking the battery motor and tires as well as the potentiometer A punctured tire is one of the more common problems that can be encountered when using a mobility scooter The pneumatic tyres in mobility scooters like all tyres are prone to punctures and should be replaced frequently The best way to avoid punctures is to replace the tyres before they wear out Pneumatic tyres are usually the preferred choice of many users due to their comfort to ride and do not require the additional security of an inner tube Depending on the type of terrain on which the scooter is used tyres with a solid infill are also considered to be safe because they are puncture proof and are hardwearing Pneumatic tyres can be damaged more quickly than solid tyres in the event of traveling on a rough terrain Another issue with wiring that could occur in the mobility scooter is when the speed potentiometer malfunctions The potentiometer is a device that takes the input voltage and sends it to the controller and converts it into an output signal It is important to ensure that it is working well so if notice the speed readings are inconsistent it could be a sign that something isnt working properly The battery needs to be replaced if there are signs of degrading or is not capable of fully charging This can be accomplished by following the instructions in the scooters user manual It is also a good idea to check the battery connections and charger regularly to ensure that they are in good condition