edwardcurve7
User Name: You need to be a registered (and logged in) user to view username.
Total Articles : 0
https://www.g28carkeys.co.uk/fiat-car-key-replacements-near-me/
Reasons Your Fiat 500 Key Fob Wont Work A Fiat 500 key fob allows you to easily open doors and start your car However there are many reasons why the fob wont be functioning This includes a dead battery water damage issues with the receiver module and interference This listing is for a NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand It has to be professionally programmed click here to search for local locksmiths for automotive locksmiths Includes lock unlock and trunk buttons Dead Coin Battery A dead battery is the most frequent cause of your 500 key fob that isnt working Key fobs of today have only a limited range of operation and must be within only a few inches from the vehicle in order to function If you are further away from your car and press the keyfob button it will not respond and display the message Key Fob Not Detected If this occurs you need to replace the battery of your coincell Part Number CR2032 by a fresh one of a reputable brand such as Panasonic Duracell or Energizer They are available at your local hardware store or on the internet You can test the coincell battery by pressing the buttons while you are standing close to your Fiat 500 The parking lights should light up and the key fob will operate the lock and unlock switches If your key fob still doesnt work even after replacing the battery there could be water damage that hinders it from communicating with the module in your vehicle Water damage can occur in a variety of ways from a light splash to submerging the fob salt water at the beach If you suspect that your fob was exposed to water put it in a bag of rice to draw out the moisture If this doesnt work you will require your fob to be replaced by an auto locksmith or a dealer Water Damage The fob does have rubber seals that keep water from the chips electronic circuit submerging it in the ocean or washing it in a machine can cause water damage Saltwater is particularly dangerous to the fobs circuit board causing it to short out and eventually end up dying If you get the fob wet its not an ideal choice but if you drop it in a glass of water or fail to take it out of your pants pocket prior to running the washer do not give up hope First take the battery off the fob Before replacing the battery clean the electronic chip using isopropyl or a similar product Check how much is a new fiat 500 key to see if it is functioning If the key doesnt function it may need to be programmed again This is typically handled by a dealer or professional auto locksmith If the key is more recent and was not programmed to your car it is likely to need to be replaced completely This is a straightforward process which can be accomplished by a professional locksmith for automotive use The locksmith will need the key cut to match your vehicles ignition The locksmith will also have to reprogram the fob into the vehicles system This is a costeffective and quick process that could be completed within the same day Receiver Module Issues One of the most common reasons why your 500 key fob wont be functioning is that its out of range The remote has a maximum range of 30 feet So if you are too far away from your vehicle it wont respond to your commands You can easily fix this by moving the remote closer to your car until it responds If youve replaced your coin battery commonly calledbutton or button or watch and your fob still wont work it could be due to an internal circuit board problem In the majority of cases reprogramming your fob will solve the problem You can find instructions on how to do this on the majority of automobiles by searching YouTube or looking through the owners manual Its possible that you need to replace the metal retaining clips that keep the coin battery If they become loose it can stop your coin battery from being properly seated and cause your remote to malfunction In rare cases the fob may be out of the vehicles sync because of hardware or software issues You can fix this issue by visiting your local dealer or autolocksmith to reprogram your key fob In some instances they might need to install the software again in your body control module too Interference Interference can also cause the key fob not to receive or transmit signals This could happen when the keyfobs location is in close proximity to a radio transmitter like a cell phone or radar detector Other reasons the key fob might not function may be a lack of connection to the buttons damage to the internal chip or water damage If your key fob suddenly stopped working or you have tried everything at home to solve the issue eg replacing the battery reprogramming it and using the spare key fob you may have a defective receiver module on your 500 The receiver module which is located beneath the dashboard receives radio frequency signals from your key fob Then it converts them into electronic commands that the vehicle interprets There is a simple way to reset the 500s inboard system including the keyfob Disconnect the 12 volt battery for about 15 minutes by disconnecting the negative cable first then the positive cable Then reconnect the battery This will remove any residual electricity and restart the cars computers which can help get your key fob working again If the problem persists you should speak with a certified technician They will be able to determine the exact cause of problems